Stop It® HP™ Leak Sealing - indumar Products TecSolutions Consultants Phoenix, Arizona. Leading distributor for underground utility locating equipment and water leak detection equipment in Arizona, New Mexico, Southern Nevada and Southern California. Products for professional plumber, locator crew, or leak detection company including pipe and cable locators, water and gas leak detection equipment, ground penetrating radar, inspection cameras, sonde, conduit rodders, utility markers and utility management. Pipe Cable Leak Locating Equipment and Training. Stop It® HP™ Leak Sealing - indumar Products TecSolutions Consultants Phoenix, Arizona. Leading distributor for underground utility locating equipment and water leak detection equipment in Arizona, New Mexico, Southern Nevada and Southern California. Products for professional plumber, locator crew, or leak detection company including pipe and cable locators, water and gas leak detection equipment, ground penetrating radar, inspection cameras, sonde, conduit rodders, utility markers and utility management. Pipe Cable Leak Locating Equipment and Training.

Stop It® HP™ Leak Sealing - indumar Products

Stop It® HP™

Maximum Pressure Performance When high-pressure pipes leak, the seepage can affect the environment, production and your company's bottom line. Fixing it quickly and securely is a must - and reinforcing the pipe walls so that it never gets to that point can save the facility significant time and money later.

With STOP IT® HP™ epoxy leak sealant, you can repair pipeline cracks and leaks and reinforce diminished pipe walls in minutes so that they can handle working pressures up to 2,000 psi. In as little as four hours, operations can be resumed, and STOP IT® HPTM exhibits maximum pressure performance after 24 hours of curing.

It's the durable solution that's trusted to repair a damaged methane gas line in the inhospitable Dakar, Africa desert. After the fiberglass pipeline was damaged by a motorized grader, Fortesa International used STOP IT® HP™ to cover 11 feet of the tube, sealing the five-foot hole and the non-visible damage from fracturing.

STOP IT® HP™ is a registered trademark of InduMar Products, Inc.

  • Surface preparation consists of removing any loose scale and lubricants or greases. The system should be relieved of all pressure until the product is fully applied and cured. Application surfaces should be dried prior to application and warmed if the pipe surface is less than 50°F or cooled if greater than 100°F.
  • Application entails mixing a pre-measured two-part sealant, wetting a fibrous reinforcement tape, and wrapping the tape onto the pipe surface.
  • Applications can be made regardless of pipe orientation.
  • Sealant mixing takes seconds and can be immediately applied to the reinforcement tape. The wetted tape possesses a working time of approximately 8-10 minutes. The exact application time will depend on the specific conditions under which STOP IT® HP is being applied.

Stop It® HP™ Leak Sealing - indumar Products
Stop It® HP™ Leak Sealing - indumar Products

Below you can view more information about The STOP IT® Pipe Repair System. If you have any questions, please call us today at 602-830-9400. For your convenience, click here to get a free quote from this site.

*Click on the Tabs to view more information.

Shelf Life: Six months from date of purchase when stored at 40° to 83°F (5° to 28°C)

Color: Component 1 - clear; Component 2 - straw; Fiber - yellow (other options available)

Mixing Ratio: As supplied, dual cartridge dispenser

Pot Life: 8-10 minutes at 72°F (22°C), after mixing for films less than ½” thick

Glass Transition Temperature: 165°F (74°C), cured and annealed

Cure Time: ~4 hour @ 72°F (22°C) at 1/8” film thickness

Sealant Viscosity: Gel-like before cure

StopIt HP™ Composite Application: Recommended for pressures up to 2,000 psi (140 kg/cm2)

Maximum Operating temperature: 165°F (74°C)

indumar Stop It HP

TShelf Life: 6 months from date of purchase when stored at 40° to 83°F (5° to 28°C)

Color: Epoxy part 1 - clear, Epoxy part 2 - straw

Mixing Ratio: As supplied, dual cartridge dispenser

Pot Life: 8 min. @ 72°F (22°C) after mixing, for mixtures less than 1/2” thick

Glass Transition Temperature: 165°F (74°C), cured and annealed

Cure Time: ~4 hour @ 72°F (22°C) at 1/8” film thickness

Sealant Viscosity: Gel-like before cure

TecSolutions Consultants is a valued supplier to the utility locating and leak detection industry in the Southwest.

If you have any questions, please call TecSolutions Consultants today at 602-830-9400. For your convenience, click here to get a free quote from this site.

Thank you for your interest in TecSolutions Consultants. We look forward to serving you in the near future.

Products Available: Pipe & Cable Locators, Leak Detection, Ground Penetrating Radar GPR, Drain & Sewer Line Jetting, Inspection Cameras, Sonde, Conduit Rodders, and Utility Management Marking Equipment.

© TecSolutions Consultants All rights reserved.
   Website Design by Brymels LLC.    Service Area   Back to top